FTC62 and FTS62

FTC62 and FTS62 high pressure float traps (DN15 – DN25)

Description

The FTC62 and FTS62 are a carbon steel bodied ball float steam trap having stainless steel working internals and automatic air venting facility.
FTC62 and FTS62 available options when facing the body:
L-R Select L-R for a flow direction of Left-to-Right
or
R-L Select R-L for a flow direction of Right-to-Left

Standards
This product fully complies with the requirements of the EU Pressure Equipment Directive/UK Pressure Equipment (Safety) Regulations
and carries the / mark.

Certification
This unit is available with certification to EN 10204 3.1.
Note: All certification/inspection requirements must be stated at the time of order placement

Sizes and pipe connections

½”, ¾” and 1″ Screwed BSP or NPT
½”, ¾” and 1″ Socket weld ends to BS 3799 and Class 3000 lbs

Standard flanges:
DN15, DN20 and DN25 Flanged EN 1092-1 PN100 †
½”, ¾” and 1″ Flanged ASME B 16.5 Class 600

Materials

FTC62 and FTS62 high pressure float traps (DN15 - DN25)

No.	Part	Material
1	Body	Carbon steel	EN 10213 1.0619+N/ASTM A216 WCB
2	Cover	Carbon steel	EN 10213 1.0619+N/ASTM A216 WCB
3	3/8″ NPT taper plug	Stainless steel	CF8 / 1.4308 or 1.4301 / 304
4	¾” UNF nut (x 6)	Carbon steel	ASTM A194 Gr. 7
5	¾” UNF studs x 85 mm long (x 6)	Carbon steel	ASTM A193 B7
6	Strainer cap	Stainless steel	CF8 / 1.4308 or 1.4301 / 304
7	Strainer screen	Stainless steel	AISI 316L
8	‘S’ type gasket	Stainless steel	AISI 304
9	Air vent assembly	Stainless steel	AISI 431 S29 + 303
10	Air vent tube	Stainless steel	ASTM A269 304L
11*	Seat clamp	Stainless steel	CF8 / 1.4308 or AISI 303
12*	M6 x 30 long cap screw (x 4)	Stainless steel	EN 150 3506-1
13	Pivot pin	Stainless steel	ASTM A276 304
14	Float assembly	Stainless steel	AISI 304L
15*	½” Ø ball	Stainless steel	AISI 316
16*	Conical spring	Stainless steel	Gr. 302 S26 Gr. 1
17	Valve seat and discharge pipe assembly	Stainless steel	AISI 431 S29 + 304L
18	Spirally wound gaskets Body to Cover and Seat to Body Graphite filler + 304 stainless strip
19
20	Name-plate	Stainless steel	204
21	Hammer drive screws (x 2)	Stainless steel	18-8
22	Baffle plate	Stainless steel	304L

Capacities

FTC62 and FTS62 high pressure float traps (DN15 - DN25)
Capacities shown above are based on condensate at saturation temperature.
Under start-up conditions when condensate is cold the internal bi-metallic air vent will be open and provides additional capcaity to the main valve.
The table opposite gives the minimum additional cold water capacities from the air vent on all sizes.
Note: The air vent closing temperature range = 120 °C to 135 °C.